4-11 you can see the four (4) alignment tabs that hold the Program Selector to the Program Selector Mounting Plate. 4-9), while holding the Locking Tab in use your other hand to bring the bottom of the Program Selector slightly away from the Mounting Plate, and then remove by sliding it up and off (Fig 4-10). Using a small screwdriver push in on the Locking Tab (Fig.Now rotate the Program Dial until the half moon cut out lines up with the Program Selector Locking Tab (Fig 4-8). With the Knob removed loosen the Phillips Screw and remove the Program Knob Bezel (Fig. To remove the Program Selector, first remove the Program Selector Knob by grasping it firmly and pulling it toward you (Fig.CONTROL PANEL COMPONENTS - Program Selector TECH NOTE: The tabs on the Switches and Potentiometers are very delicate and can easily snap off. 4-5 Potentiometer you can see the positioning tabs. Using a small screwdriver press the tabs inward then slide the Switch or Potentiometer out from the rear of the Control Panel. The Switch and Potentiometers are held in place by four (4) positioning tabs (Fig. To remove either the Switches (A) or the Potentiometers (B), first remove the Button and/or Knob.− To remove the Knobs (B) or the Program Dial (C), grasp the firmly and pull straight out toward you. − To remove a Push Button (A), first mask the area to protect against damaging the Control Panel, then carefully insert a small screwdriver between the bottom of the Button and the Control Panel (Fig. The Control Panel has three main controls Push Buttons (A), Knobs (B) and the Program Dial (C).CONTROL PANEL COMPONENTS - Switches and Potentiometers A 3-6) and the complete Control Panel Assembly can be removed. Now release the two (2) remaining Control Panel Locking Tabs located on the bottom rear of the Control Panel (Fig. To remove the Switch wiring simply press the Locking Tab forward and slide the Wiring Connector up and out (Fig. Next, remove the wiring from each Switch and the Program Selector.TECH NOTE: When re-installing the Control Panel make sure the bottom edge of the Soap Dispenser Housing rests on top of the Control Panel opening as shown in the box of Fig. With the Soap Dispenser and Door completely removed you can remove the two (2) remaining Phillips Screws. 3-3) the pin will easily slide up and out. Now, remove the Dispenser Door and Program Guide by lifting out the Hinge Pin (Fig. Next, remove the Soap Dispenser by grasping it firmly and sliding it out from its housing (Fig.To remove the Control Panel, first remove the two Phillips screws located on the top corners of the Control Panel (Fig 3-1).
ARISTON WASHER DRYER COMBO MANUAL MANUAL
REPAIR MANUAL SAFE SERVICE PRACTICES AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 Page: iġ. All access panels are properly and securely reassembled. All safety grounds (both internal and external) are correctly and securely connected. are adequately spaced away from metal parts or panels. All non-insulated electrical terminals, connectors, heaters, etc. Electrical leads are properly dressed and secured away from sharp edges, high temperature components and moving parts. 6) Prior to returning the appliance back into active service, ensure the following: - All electrical connections are correct and secure. Failure to do so will result in a hazardous condition being created. 5) It is extremely important that all safety ground connections be reestablished prior to the completion of the service call. 4) Use only genuine factory replacement parts as substitutions may interfere with compliances to home safety codes or standards. 3) Never interfere with the proper operation of any safety device. 2) Before servicing or removing an appliance: - Disconnect power to the appliance. Examples of safe service practices are listed below but are not limited to the following: 1) Never attempt a product repair if you have any doubts as to your ability to complete the repair in a safe and satisfactory manner. If you have any questions regarding the proper diagnosis, repair or operation of any Ariston Appliance, please contact the Ariston Customer Care Center or your Service Representative SERVICING SAFEGAURDS: To avoid personal injury and/or property damage, it is important that safe servicing practices be observed at all times. Ariston cannot be responsible, nor assumes any liability for injury or damages of any kind arising from the use or misuse of the information contained in this Repair Manual. This Repair Manual is intended for persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the Appliance Service Industry.
0 kommentar(er)
